Tools

The PK-5 includes over 90 of our best shop tools selected with versatility in mind. A great way to outfit a pro bench or to set up a dream home workshop. The PK-5 is an impressive, professional set of specialty tools that can help you perform hundreds of bicycle repair and maintenance procedures. An investment you'll use and appreciate for decades. Kit Includes: - ATD-1.2 Adjustable Torque Driver - AWS-1 Three-Way Hex Wrench Set: 4, 5, 6mm - AWS-3 Three-Way Hex Wrench Set: 2, 2.5, 3mm - BBT-10.2 Adjusting Cap Tool: For 8-Spline Hollowtech II - BBT-22 Bottom Bracket Tool - BBT-69.2 Bottom Bracket Tool - BO-2 Bottle Opener - CBW-1 Open End Wrench: 8/10mm - CBW-4 Open End Wrench: 9/11mm - CC-4 Chain Checker - CN-10 Professional Cable and Housing Cutter - CNW-2 Chainring Nut Wrench - CP-1.2 Cassette Pliers - CT-3.3 Chain Tool - CWP-7 Compact Universal Crank Puller - DAG-2.2 Derailleur Hanger Alignment Gauge - DH-1 Dummy Hub - DP-2 Threaded Dummy Pedal - DSD-2 Derailleur Screwdriver: Cross Tip - DSD-4 Derailleur Screwdriver: Flat Blade - DT-2 Rotor Truing Fork - FR-5.2H Cassette Lockring Tool with Handle - GSC-1 GearClean Brush - HMR-8 8 oz. Shop Hammer - HXS-1.2 Hex Wrench Set - MLP-1.2 Master Link Pliers - NP-6 Needle Nose Pliers - PAW-6 6" Adjustable Wrench - PH-1.2 P-Handle Hex Wrench Set - PW-4 Professional Pedal Wrench - RR-12 Tape Measure - SBC-1 Spoke, Bearing and Cotter Gauge - SBS-1.2 Socket and Bit Set - SCW-13 13mm Shop Cone Wrench - SCW-14 14mm Shop Cone Wrench - SCW-15 15mm Shop Cone Wrench - SCW-16 16mm Shop Cone Wrench - SCW-17 17mm Shop Cone Wrench - SCW-18 18mm Shop Cone Wrench - SCW-19 19mm Shop Cone Wrench - SP-7 Side Cutter Pliers - SW-0 Precision Spoke Wrench: .127" - SW-2 Precision Spoke Wrench: .136" - SWR-8 3/8" Drive Ratchet Handle - SZR-1 Shop Scissors - TL-1.2 Tire Lever Set - TL-4.2 Tire Lever Set - TL-6.2 Steel Core Tire Levers - TWS-1 Torx Compatible Wrench Set - UP-SET Utility Pick Set - VC-1 Valve Core Tool - ZP-5 5" Flush Cut Pliers

Updated to fit an even wider range of hub, wheel and tire combinations with room to spare, utilizing a wider base structure and larger calipers. More accurate and easier to calibrate, the versatile TS-4.2 is solidly built to accurately self-center nearly any diameter wheel 16-inch to 29+ and any tire width up to 5-inches+. - Both uprights move simultaneously to always keep wheel centered in the stand - Accommodates tire widths up to 5-inches+ with or without brake rotor mounted - Speed knob to quickly change axle widths - Accommodates hub widths from 75mm to over 250mm - Precise operation and adjustability - Built in thru-axle adaptors - Machined, welded, assembled and calibrated in our factory in St. Paul, MN - Chrome plated and powder coated heavy gauge steel construction - Removable, replaceable nylon caliper tips to protect painted/anodized rims

Proper frame preparation is very important. Park Tool's Head Tube Reaming and Facing Set combines reaming and facing of the head tube to create a perfect fit for most sizes of head cups. Includes: • 30.1 mm reamer (part #751.2) and four different size pilots (29.8mm, 30.0mm, 33.8mm, and 36.8mm) • 690 facer • Quick-release, quick-adjust feature: bottom portion slides off and on easily without threading SHIS terminology: The HTR-1 as stock will face frames of EC29, EC30, EC34 and EC37. It will ream frames of EC30. Accessories will allow service in other standards.

The SHX-1 Slide Hammer Extractor is a professional solution specifically designed for removing press fit cartridge bearings from bicycle components. Utilizing expanding collets, an extendable shaft, and a substantial (960g) slide hammer, the SHX-1 securely yet forcefully drives out cartridge bearings with targeted impact. The SHX-1 is compatible with cartridge bearings with inner diameters from 6 to 32 millimeters, covering most press fit applications found on bicycles including hubs, suspension linkages, and bottom brackets. - Set of 5 expanding collets covers most bicycle bearing IDs from 6mm to 32mm - Slide hammer shaft is extendable from 6.5" (165mm) to 13" (233mm) for additional force when needed - Organized in a convenient storage case

We put together this set of carefully chosen tools to do basic maintenance and cleaning as well as perform a wide variety of repairs and adjustments on just about any bicycle. A perfect way to start or add to your collection of shop-quality bicycle tools. The AK-5 includes a tough toolbox to protect your investment. Kit Includes: - AWS-1 3-Way Hex Wrench - BBB-4 Big Blue Book of Bicycle Repair - CC-4 Chain Checker - CM-5.3 Cyclone Chain Scrubber - CN-10 Professional Cable and Housing Cutter - CNW-2 Chainring Nut Wrench - CT-3.3 Chain Tool - DCW-1 Double-Ended Cone Wrench: 13/14mm - DCW-2 Double-Ended Cone Wrench: 15/16mm - DCW-3 Double-Ended Cone Wrench: 17/18mm - DH-1 Dummy Hub - DT-2 Rotor Truing Fork - FR-5.2 Cassette Lockring Tool - GSC-1 GearClean Brush - HCW-16.3 Chain Whip/Pedal Wrench - HXS-1.2 Professional L-Shaped Hex Wrench Set - MLP-1.2 Master Link Pliers - PAW-12 12" Adjustable Wrench - RR-12 Tape Measure - SD-2 #2 Phillips Screwdriver - SD-3 3mm Flat Blade Screwdriver - SW-0 Precision Spoke Wrench: .127" - SW-2 Precision Spoke Wrench: .136" - TL-1.2 Tire Lever Set - TWS-3 Torx Compatible 3-Way Wrench - VC-1 Valve Core Tool

ShockWiz is a suspension tuning system for air-sprung mountain bikes that combines high-tech hardware with an intuitive smartphone app. It's lightweight, durable and powered by a long-lasting coin cell battery, ShockWiz automatically records and evaluates suspension performance every time you ride. The ShockWiz app displays straightforward adjustments that unite bike, terrain and riding style. ShockWiz works for all mountain bike riders, regardless of their experience or bike's intended use. It works on hardtail and dual suspension bikes, and for all levels of skill, speed, and terrain. With ShockWiz, you know exactly how your suspension is performing – and how to make it better. Features & Benefits: - Automated tuning recommendations - Shock tuning score - a snapshot of how well your suspension is set up for you - Works on hardtail and dual suspension bikes. Works for Cross-Country, Trail, All Mountain and Downhill. - Inexpensive, replaceable CR2032 battery lasts for months - Waterproof and dustproof - IP67 rating - Two alternative hoses (included) offer a range of fitting options - Smartphone app is compatible with Apple and Android phones Essential Details: - ShockWiz is designed for all mountain bike riders, regardless of your experience or bike's intended use. - You can tune for every riding style: Efficient (pedaling), Balanced, Playful or Aggressive. - Advice for air pressure, spring rate, compression and rebound is displayed in the intuitive smartphone app. - In the box: ShockWiz hardware, two hoses, rubber mounting boot and zip ties.

The BX-2.2 features updated pallet configuration and storage options to help you keep your tools secure and easily accessible. The expanded custom designed tool pallets, including dual-sided pallet wings, are all housed in a virtually indestructible composite travel case. Designed and built for the traveling mechanic who demands the best! - Custom designed tool-holding pallets with loops and pockets - Folding, dual-sided pallet wings - Front tool pallet that stores securely inside during transport - Dent-proof composite shell built around an aluminum frame - Key lock - Nominal dimensions: 19" x 14.85" x 8.5" (48.25 cm x 37.7 cm x 21.6 cm), 13.2 lbs. (6 kg)

The 791 Reamer Set reamer is used on the PF30 frame shells. The reamer is sized at 45.94mm. The 791 Reamer Set must used with the HTR-1 Head Tube Reamer and Facer, a 750.2 Centering Cone and the 690-XL Facer. The 791 set also includes a pilot that allows a facing-only option of the PF30 frame shell.

Park Tool's 692 Left-Hand Bottom Bracket Tap is a 1.370" x 24 TPI replacement tap for the BTS-1 Bottom Bracket Tap Set. This tap is used on the drive side (right side) of the bike. This side of the bottom bracket uses a counter-clockwise or left-hand thread. Note: It is very important to have sharp and accurate cutting tools for effective tapping and thread-chasing. Using an excessively worn or damaged tap can cause permanent damage to the frame and/or bottom bracket.

Turbo S Diagnosis Tool from Specialized.

Park Tool's Crown Race Cutter Adaptor is used in conjunction with the CRC-1 Crown Race Cutting Tool (sold separately) to machine 39.8mm crown race seats (1.5” standard) on tapered forks with 1-1/8” steerer tubes. It includes a precision-machined adaptor body and a 39.8mm high-speed steel crown race cutter. The CRC-15 will work on forks with a maximum 1.5-inch taper of 4.25 inches.

Park's HHP-2 accurately aligns and presses 1-, 1-1/8-, 1-1/4- and 1.5-inch headset cups into your frame's headtube. It features a quick-release design for fast tool installation and removal, extra-long handles for superior leverage and stepped bushings for precise cup alignment. This versatile tool also presses cartridge bearings and cups into one-piece bottom bracket shells and holds fixed-cup wrenches in place when removing or installing adjustable-type bottom brackets.

The 2197 is an add-on accessory for the Park Tool DT-5 and DT-5.2 Disc Brake Mount Facing Set to enable easier and more efficient facing of disc brake mounts on carbon fiber frames. Features a brazed-on diamond grit surface that is over 100 times more durable and effective on carbon fiber than the cutter included with the DT-5.2. The 2197 sits between the cutter of the DT-5.2 and the brake mount, and smoothly and evenly grinds the mounting surface until it is flat and properly perpendicular to the rotor. NOTE: The 2197 is intended for facing carbon fiber only. Aluminum, steel, and titanium disc brake mounts should be faced using the #2171 facing cutter included with the DT-5.2. For carbon frames that feature aluminum inserts (with a carbon/aluminum hybrid mounting surface), use the #2197. When machining carbon fiber, regularly apply water (or a similar solution) to the cutting surface.

A perfect way to start a bicycle tool collection! A great combination of tools to help a home mechanic clean, adjust, maintain, and do some basic repairs on their bike. The SK-4 includes more than 15 genuine Park Tool products that can perform dozens of tasks and includes a custom Park Tool toolbox with extra room for spare parts and more tools. The SK-4 includes: - AWS-10 Fold-Up Hex Wrench Set - BBB-4 Big Blue Book of Bicycle Repair - CC-3.2 Chain Checker - CN-10 Professional Cable and Housing Cutter - CT-5 Mini ChainBrute Chain Tool - FR-5.2 Cassette Lockring Tool - GSC-1 GearClean Brush - HCW-16.3 Chain Whip/Pedal Wrench - HR-8 8mm Hex Wrench - MLP-1.2 Master Link Pliers - SD-2 Shop Screwdriver: #2 Phillips - SW-7.2 Triple Spoke Wrench - TL-1.2 Tire Lever Set - TWS-3 Torx Compatible 3-Way Wrench

The 37-piece SBS-3 from Park Tool is a comprehensive, shop-quality set of sockets, hex bits, and Torx compatible drivers selected specifically to tackle a wide variety of common bike repair needs. The SBS-3 also includes flat-faced sockets in common sizes for work on suspension forks. Ideal for use with Park Tool torque wrenches, the 3/8" drive bits and sockets are forged from tough, chrome vanadium steel and nickel chrome plated for lasting durability.

Designed and built specifically for a wide variety of bicycle hex work the THH-1 is a set of eight common sizes of professional quality T-Handle hex wrenches built for speed, efficiency, leverage and a perfect fit. Soon to become your favorite hex set, the THH-1 includes a handy tool holder that mounts to any vertical surface, including pegboard and solid surfaces (fasteners not included). - Carefully selected combination of Chrome Vanadium and S-2 tool steels - 2, 2.5, 3, 4, 5, 6, 8 and 10mm hex wrenches included - Unique anodized aluminum Speed Spinner makes running long bolts in and out quick and effortless - Machined, chamfered tips allow easier insertion into hex fittings - Integrated “Strip-Gripper” twisted hex that makes removal of most bolts with stripped or over-sized hexes fast and easy - Sliding T-handle creates increased leverage and multiple access positions - Tool holder is included with the set and mounts to any wall, bench or tool box, perfectly positioning each wrench for easy access and storage

World-famous Park Tool quality wrapped up in a great set of metric combination wrenches. The MWR-SET includes 6mm to 17mm wrenches with a 12-point two-way ratcheting box end. Forged from chrome vanadium steel, chrome-plated, meticulously polished, then center dipped in Park Tool blue vinyl for a positive grip. Strong, comfortable, and beautiful! - Includes 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, and 17mm wrenches

The BKM-1.2 Hydraulic Brake Bleed Kit will bleed most models of mineral oil-based hydraulic bicycle disc brakes, including models made by Shimano®, Magura®, TRP®, Tektro®, Trick Stuff®, SRAM® DB8, Campagnolo®, Promax®, and Clarks®. Bleeding of hydraulic brakes removes air bubbles and contaminants from the braking system, for long-lasting components and peak performance. The BKM-1.2 is built for the rigors of daily commercial use and includes two syringes, hoses with shutoff clips, multi-size bleed blocks, a bleed funnel, and a set of our unique mountable syringe holders, as well as multiple hose fittings to fit the multiple standards found on hydraulic bicycle brake systems. Every part is replaceable and available from Park Tool. Housed in a rugged storage case. Includes: -  Two 20 mL syringes -  Two hose assemblies with shutoff clips -  One hose assembly with integrated fitting for bleed nipples such as those found on Shimano® mineral oil brake systems -  One open-ended hose assembly -  Bleed funnel with stopper -  Two 10 mm/12 mm universal bleed blocks -  Two 11 mm bleed blocks -  Two adjustable syringe holders -  M4 x 0.7 adapters — SRAM® DB8, Trick Stuff®, Campagnolo® (x2) -  M5 x 0.8 adapter — Formula™ Cura™, Tektro®, Hayes® (x2) -  M6 x 0.75 adapter — Magura® -  M6 x 1.0 adapters — universal (x2) -  M6 x 1.0 adapter — Promax® -  M7 x 0.75 adapter — Shimano® -  Hose compression sleeve — universal -  Fluid disposal bag -  Set of spare O-rings and hose -  Replacement parts available -  Brake fluid not included NOTE: The BKM-1.2 is for mineral oil-based hydraulic bicycle brake systems only. DOT fluid and mineral oil should never be mixed in the brake system or in their respective service tools. Cross-contamination of brake fluid may cause seal failure which may result in brake failure. For brakes using DOT fluid use the Park Tool BKD-1.2 Hydraulic Brake Bleed Kit — DOT.

For easy and safe servicing of your RockShox rear shock, look no further than the RockShox Rear Shock Clamp Tool. Use with model-specific clamp tips for servicing the damper of your rear shock. - For rear shock damper servicing - Ratcheting pistol grip action for easy operation - Use with shock-specific clamp tips

Designed and built specifically for a wide variety of bicycle Torx compatible work, the THT-1 is a set of eight common sizes of professional quality T-Handle star-shaped wrenches built for speed, efficiency, leverage and a perfect fit. Soon to become your favorite Torx compatible set, the THT-1 includes a handy tool holder that mounts to any vertical surface, including pegboard and solid surfaces (fasteners not included). - Carefully selected combination of Chrome Vanadium and S-2 tool steels - T6, T8, T10, T15, T20, T25, T30 and T40 Torx compatible wrenches included - Unique anodized aluminum Speed Spinner makes running long bolts in and out quick and effortless - Sliding T-handle creates increased leverage and multiple access positions - Tool holder is included with the set and mounts to any wall, bench or tool box, perfectly positioning each wrench for easy access and storage

No more need to hold wheels between your knees, balance on a bench top or ask for help. The WH-1 Wheel Holder firmly holds thru axle and quick release wheels at three convenient positions. It’s like having a strong helper to hold wheels during cleaning, tire and tube work, hub work, cassette work, and tubeless installation. The WH-1 can be bolted or clamped directly to a bench or installed in a bench vise. Uses and Features: - Quick and easy access to hold virtually any wheel to perfectly position your work for a variety of tasks including but not limited to: - Wheel building -Cassette removal and installation - Tire and tube removal and installation - Tubeless tire work - General cleaning - Hub work - Holds wheel at vertical, 35 degrees from vertical, and horizontal positions - Accepts 12, 15, and 20mm thru axles and 5mm skewers - E-Nickel finish for durability

The BKD-1.2 Hydraulic Brake Bleed Kit will bleed most models of DOT fluid-based hydraulic disc brakes, including models made by SRAM®, Formula®, Hayes®, and Hope®. Bleeding of hydraulic brakes removes air bubbles and contaminants from the braking system, for long-lasting components and peak performance. The BKD-1.2 is built for the rigors of daily commercial use and includes two syringes, hoses with shutoff clips, multi-size bleed blocks, and a set of our unique mountable syringe holders, as well as multiple hose fittings to fit the multiple standards found on hydraulic bicycle brake systems. Every part is replaceable and available from Park Tool. Housed in a rugged storage case. Includes: - Two 20 mL syringes Two hose assemblies with shutoff clips - Two 10 mm/12 mm universal bleed blocks - Two 11 mm bleed blocks for Hayes® systems -  Two adjustable syringe holders -  M5 x 0.8 adapters— SRAM® (x2) -  M6 x 1.0 adapter— universal (x2) - Bleeding Edge-specific fitting — SRAM® -  Hose compression sleeve — universal -  Set of spare O-rings and hose -  Replacement parts available -  Brake fluid not included NOTE: The BKD-1.2 is for DOT fluid-based hydraulic bicycle brake systems only. DOT fluid and mineral oil should never be mixed in the brake system or in their respective service tools. Cross-contamination of brake fluid may cause seal failure which may result in brake failure. For mineral oil brake systems use the Park Tool BKM-1.2 Hydraulic Brake Bleed Kit — Mineral Oil.

The CRS-15.2 uses two different insert rings to install bearing races on the 1.5-inch and 1-1/4-inch forks. The bearing surface is spared a direct hit by using aluminum inserts. Using a hammer, tap firmly on the end cap of the tube and seat the race into its proper place safely and accurately. Included extension allows work on fork steering tubes up to 425mm. - SHIS terminology: The CRS-15 services crown races in SHIS 33 and 40.

A complete tool set to work on both Campagnolo and Fulcrum Ultra-Torque and Power Torque crank and bottom bracket systems (each sold separately). The CBP-8 includes a beefed-up bearing and crank puller and all the fittings necessary to remove and install both systems. - Bearing Puller That Fits Both Power Torque And Ultra-Torque - Crank Puller For Power Torque - Bearing Setter For Both Power Torque And Ultra-Torque - Removal Adaptor For Power Torque Crank Bearings - Removal Protection Pads For Use With Carbon Cranks - Removal Protection Adaptor For Use With Aluminum Crank Arms - Crank Removal Extension Plug For Power Torque

• Use to remove air shaft and damper shaft • Reverse threaded • See RS1 Service Manual for instruction

The SRAM Pro Disc Brake Bleed Kit is designed for servicing SRAM disc brakes systems. - Kit includes 2 syringes, fittings, bleed blocks, Torx tool, crowfoot, Bleeding Edge Fitting, and DOT5.1 hydraulic fluid - For use with SRAM X0/ XX/ Guide/Level/Code/HydroR/G2 disc brakes - Compatible with DB-G2-R-A1, DB-G2-R-A2, DB-G2-RE-A2, DB-G2-RS-A1, DB-G2-RS-A2, DB-G2-RSC-A1, DB-G2-RSC-A2, DB-G2-ULT-A1, DB-G2-ULT-A2, DB-GDE-R-A1, DB-GDE-R-B1, DB-GDE-RE-A1, DB-GDE-RS-A1, DB-GDE-RS-B1, DB-GDE-RSC-A1, DB-GDE-RSC-B1, DB-GDE-T-A1, DB-GDE-ULT-A1, DB-LVL-A1, DB-LVL-T-A1, DB-LVL-TL-A1, DB-LVL-TLM-A1, DB-LVL-TLM-B1, DB-LVL-ULT-A1, DB-LVL-ULT-B1, DB-X0-B1, DB-XX-A2

- Premium syringes offer enhanced clarity, improved durability, and ergonomic handles. - Innovative quarter-turn valves make it easy to quickly open and close the bleed system. - Straight and 90-degree clips keep the syringe upright to lend an extra hand to the technician. - Includes bleed blocks for most popular 2-piston and 4-piston brake calipers. - Available separately for DOT fluid and mineral oil systems, each kit contains adapters for nearly all disc brake systems on the market. - Deluxe case keeps small parts organized and protected. -01: (Black Seal) : fit most DOT fluid brakes from Avid, SRAM, Formula, Hayes, and Hope -02: (Red Seal) : fit most mineral oil brakes from Shimano, Magura, Tektro, TRP, and Hayes

The key to wheels that are strong and reliable is having spokes that are properly and uniformly tensioned. Park's Spoke Tension Meter accurately and reliably measures the absolute tension of each of the spokes in a wheel, as well as the relative tension between all the spokes in a wheel. It's easy to use, affordable and it works on nearly any bicycle spoke, no matter its diameter, material or shape.

With today’s lightweight components, torque wrench use in the shop is no longer an option — it’s a must for every mechanic. The TW-6.2 is a high-quality, ratcheting, click-type torque wrench that accurately measures and applies the proper amount of torque to a component’s threaded fastener(s). Designed for higher torque settings for repairs and installation in the bottom bracket, cassette lockring and other areas that use a higher torque settings. For lower torque setting, see the TW-5. Comes with its own protective case. - 10–60 Newton meter range (88–530 Inch Pounds) - Adjustable in 0.25 Nm increments - Ratcheting 3/8" drive - Reads and registers for both left hand and right hand threading - Dial-adjust system allows desired torque setting to be preset - Calibrated to be accurate to +/- 4% - Length: 36.2cm (14.25")

Park Shop Cone Wrenches are made of thin tool steel to fit the low-clearance adjusting nuts and cone flats on hubs and other bearing assemblies. Their special Y-heads put more material where it's needed for greater strength. Most applications require several cone wrenches, so Park gives you a whole set, featuring 13mm - 24mm, 26mm and 28mm wrenches to suit your repair needs.

Designed and built with the specific needs of the bike mechanic in mind. The RP-SET.2 includes five professional quality pliers for internal snap rings and one for external snap rings. Pliers are made from forged, heat treated cro-moly steel with a return spring and vinyl dipped grips. RP-1: .9mm straight internal. Opens from 22mm down to 0 (tips touching) RP-2: 1.3mm bent internal. Opens from 22mm down to 2mm (center to center) RP-3: 1.3mm bent external. Opens from 2mm (center to center) up to 18mm RP-4: 1.7mm bent internal. Opens from 21mm down to 2mm (center to center) RP-5: 1.7mm straight internal; Opens from 25mm down to 0 (tips touching)

The DAG-2.2 is an indispensable shop tool that can be used to both measure and straighten misaligned derailleur hangers solving a high percentage of shifting problems. - Gauge bar made of heavy gauge, chrome plated steel - Adjusts to fit 20" to 29"+ wheels - Replaceable threaded tip - Upgraded large inner shaft for added strength* - Tighter tolerances for improved accuracy* - Improved clearance and reach to fit more frame/hanger combos including low clearance thru-axle derailleur hangers* *Compared to DAG-2

Park's Tire Seating Tool is designed to quickly seat the bead on stubborn tires. During inflation some tire beads can slip below the rim edge and become difficult to pull out and align. The PTS-1 comes to the rescue with its non-slip jaws and vinyl-coated handles that provide plenty of leverage for pulling out the tire. Plus, it's adjustable to fit various tire widths.

Quickly, safely and easily set your crown race with Park's CRS-1 Crown Race Setting System. It includes 6 different inserts (3 for 1-inch and 3 for 1-1/8-inch steerer tubes) that ensure full contact with the crown race for precision installation.

Never be left looking for an errant wrench when you have Park's Metric Wrench Set. It includes 12 high quality Park metric wrenches from 6 to 17mm in diameter, featuring both box and open ends. They are all forged from chrome vanadium steel, then chrome plated for durability and dipped in Park Tool blue vinyl for outstanding comfort and ease of use.

Engineered for fit, function, and leverage, these L-shaped shop-quality hex wrenches are a must have for every workshop. - High-torque, industrial steel wrenches - Straight hex shaft on the short side, ball end on the long side - Includes 2, 2.5, 3, 4, 5, 6, 8, and 10mm - Comfortable, ergonomically designed nylon handles fit perfectly in your hand - Durable wall/pegboard mount tool holder allows easy access and organization

With today’s lightweight components, torque wrench use in the shop is no longer an option — it’s a must for every mechanic. The Park Tool TW-5.2 is a high-quality, ratcheting, click-type torque wrench that accurately measures and applies the proper amount of torque to a component’s threaded fastener(s). With a range of 2-14Nm, the TW-5.2 is designed for the lower torque settings that a shop or consumer would use for proper seat post, seat clamp and handlebar / stem applications. Comes with its own protective case.

This handy tool will save time and frustration! Quickly and accurately cuts hydraulic brake line then precisely installs hose barbs into the tubing when the brake line is either on or off the bike. - Cuts hydraulic brake hose (does not cut steel braided hydraulic hose) - Installs press-in style barbed hose inserts - Replaceable parts including push pin tip and stainless steel blade - Hard anodized body for improved tool wear - Lightweight, CNC machined aluminum body Replacement parts: - 2494K Cutting Blade (set of 2) - 2497 Push Pin Tip

Performing the right maintenance on your SRAM and RockShox products not only ensures years of worry-free riding, but will also keep performance optimal and enhance your experience on the bike. Each service interval indicates the maximum number of riding hours designated for each type of recommended maintenance. Depending on the terrain and environmental conditions in your location, your riding style, and skill level, you may see more optimum performance if you service your SRAM and RockShox products at shorter intervals.

Performing the right maintenance on your SRAM and RockShox products not only ensures years of worry-free riding, but will also keep performance optimal and enhance your experience on the bike. Each service interval indicates the maximum number of riding hours designated for each type of recommended maintenance. Depending on the terrain and environmental conditions in your location, your riding style, and skill level, you may see more optimum performance if you service your SRAM and RockShox products at shorter intervals.

Performing the right maintenance on your SRAM and RockShox products not only ensures years of worry-free riding, but will also keep performance optimal and enhance your experience on the bike. Each service interval indicates the maximum number of riding hours designated for each type of recommended maintenance. Depending on the terrain and environmental conditions in your location, your riding style, and skill level, you may see more optimum performance if you service your SRAM and RockShox products at shorter intervals.

Engineered for fit, function, and leverage, these L-shaped shop-quality Torx compatible wrenches are a must have for every workshop. - High-torque, industrial steel wrenches - Torx compatible drivers at each end - Includes T6, T8, T10, T15, T20, T25, T30, and T40 - Comfortable, ergonomically designed nylon handles fit perfectly in your hand - Durable wall/pegboard mount tool holder allows easy access and organization

Service kit to assist in scheduled maintenance and/or rebuild of RockShox dropper seatposts.

Service kit to assist in scheduled maintenance and/or rebuild of RockShox dropper seatposts.

- 200 HOUR/1 YEAR SERVICE KIT (INCLUDES DUST SEALS, FOAM RINGS, O-RING SEALS, CHGR2 DAMPER SEALHEAD, DEBONAIR (SILVER) SEALHEAD—ZEB SELECT+/ULTIMATE A1 (2021)

Internal components for servicing the Reverb and Reverb Stealth mechanism.

Jagwire's Pro DOT Bleed Kit comes with the right fittings to bleed Avid, Formula, Hayes and Hope hydraulic-disc brakes for optimum braking performance. You can buy it with or without Finish Line DOT brake fluid.

"Take the guesswork out of internal routing. The IR-1.3 speeds the installation of internally-routed cable, housing, electronic wiring and hydraulic hose into carbon fiber, titanium, and aluminum frames. The straightforward guide magnet system utilizes five long guide cables with unique fittings, which can be routed through the frame in a number of ways using the included guide magnet. Everything is neatly stored in a convenient compact case. A true time and frustration saver!??Includes five 188 cm (74"") guide cables with attached magnets and unique fittings: • Barbed adapter — Threads into the end of brake & shift cable housing as well as hydraulic brake hose • Rubber adapter — Securely holds electronic shifting wire such as Shimano® Di2, SRAM® RED® eTAP®, FSA® K-Force® WE®, and Campagnolo® EPS • Di2®-specific adapter — Specially-designed connector clips into the end of Shimano® E-tube® Di2® shift wire, and is perfectly sized to fit into frame holes as small as 6 mm • Di2® EW-SD300-specific adapter — Specially-designed connector clips into the end of Shimano® E-tube® Di2® EW-SD300 shift wire • Reverse-polarity magnet — Used in conjunction with any of the other guide cables - feeds into the opposite end and meets the leading cable in the middle, aiding in routing on frames with tricky interior shapes Also included: • Double-threaded barb — Securely attaches new housing or hydraulic hose to existing housing or hose, allowing for easy replacement without redoing the routing • Guide magnet — routes guide cables through the frame from the outside"

Onboard mechanic. For rapid repairs, the STASH system holds a quick-draw Cannondale 10-in-1 mini tool, CO2 inflator spacer and tire plug kit beneath the water bottle. Where it thrives: On the bike, challenging trails What it's built for: Versatility, convenience Highlights: - Fastest access to tools during riding or racing - Compatible with 2021+ Scalpel - Includes holder, Dynaplug, multi-tool and CO2 spacer

Keep your most commonly used tools close at hand with this clever, multi-function tool holder. The TK-4T was painstakingly designed with pockets and holders for specific tool shapes and sizes as well as some generic storage areas. The Tool Kaddie rotates for easy access and is molded from a durable composite material. - Bench Top Mount sits firmly on any flat surface - Specific slots and holders for 3-way hexes, screwdrivers, P-Handles, pliers/cutters - Generic slots and holders to hold a wide variety of tools and small parts - Mounting location to directly attach HXH-2P or HXH-2T P-Handle Holders (sold separately) - Built-in receiver port for PTH-1 Paper Towel Holder (sold separately)

- A 37 function tool with pretty much everything you need to work on a bike - Two piece design allows for easy access of all tools -29 pro-quality vanadium steel tools: 1.5-L22-L2.534568 hex wrenches and 10mm hex socket T10T15T20T25 Torx wrenches 14/15g

Shop-quality, adjustable torque driver that limits torque applied to fasteners, preventing over-tightening and damage to lightweight components. The ATD-1.2 features all-metal internal construction with a comfortable, ergonomic composite molded grip. Each tool is assembled and calibrated at Park Tool's factory in Minnesota.

The DC-2 is a vernier caliper for accurately measuring seat posts, head tubes, bearings, spoke diameters, and other components, featuring a large LCD screen for accuracy and ease of use. The tool’s ability to measure in metric and inches in external, internal, depth, and stepped dimensions make it an indispensable shop tool. - Range: 150 mm | 6" - Resolution: 0.01 mm | 0.0005" - Accuracy: +/- 0.02 mm | 0.001" - Repeatability: +/- 0.01 mm | 0.0005" - Measures external, internal, depth, and stepped dimensions - Uses LR44 batteries

- Lyrik and Pike 29+ Dual Position Air A1 1 year service kit - Includes dust seals, foam rings, o-ring seals, Charger sealhead, DPA sealhead

- Pike Dual Position Air A1 1 year service kit - Includes dust seals, foam rings, o-ring seals, Charger sealhead

Securely holds the TS-4.2 Professional Wheel Truing Stand and tilts 20 degrees from front to back for comfortable wheel work and sight lines at any bench height. Features a wide, sturdy base, small parts compartments, spoke wrench holders, and is constructed of a durable composite material.

- Pedal thread inserts are used to replace damaged threads in cranks

200 HOUR/1 YEAR SERVICE KIT (INCLUDES DUST SEALS, FOAM RINGS, O-RING SEALS, CHARGER DAMPER SEALHEAD, DUAL POSITION AIR SEALHEAD) - (DPA ONLY) SELECT A2+ (2023+)

Performing the right maintenance on your SRAM and RockShox products not only ensures years of worry-free riding, but will also keep performance optimal and enhance your experience on the bike. Each service interval indicates the maximum number of riding hours designated for each type of recommended maintenance. Depending on the terrain and environmental conditions in your location, your riding style, and skill level, you may see more optimum performance if you service your SRAM and RockShox products at shorter intervals.

Performing the right maintenance on your SRAM and RockShox products not only ensures years of worry-free riding, but will also keep performance optimal and enhance your experience on the bike. Each service interval indicates the maximum number of riding hours designated for each type of recommended maintenance. Depending on the terrain and environmental conditions in your location, your riding style, and skill level, you may see more optimum performance if you service your SRAM and RockShox products at shorter intervals.